MCX-6100 CH 6027/14 charcterization

Date Issued
2015-11-18
Keywords
Detonasjon
Hastighet
Sedimentasjon
Project number
2015/02185
Permalink
http://hdl.handle.net/20.500.12242/1167
Collection
Rapporter
15-02185.pdf
Size: 2M
Abstract
MCX-6100 is a composition developed and produced by Chemring Nobel AS. It is a melt-cast composition primarily applicable as filler in large calibre munitions like 120 mm and 155 mm. We have characterized MCX-6100 from its potential for utilization in these types of ammunition. MCX-6100 has DNAN as binder. The solid filler is a mix of NTO and RDX. Nominal content for MCX-6100 is 32/53/15 (DNAN/NTO/RDX). The choice of DNAN as binder makes it possible to use the same filling plants as for TNT or TNT based compositions to fill MCX-6100 into warheads. The quality of the casted test items of MCX-6100 with regard to density and homogeneity has been varied. X-ray of a cylindrical charge of CH 6027/14 shows lower density in the top than in the bottom. Bubbles and pores are observed in the upper part of the charge, even though vacuum was applied during the casting. The casting process has therefore potential for improvement. MCX-6100 CH 6027/14 has been characterized with regards to critical diameter, detonation velocity and detonation pressure. Sedimentation was studied by analyses of content in the longitudinal direction of the fillings. Critical diameter for MCX-6100 CH 6027/14 is measured to 18.5 mm and 19.0 mm for two tested conical charges. The average detonation velocity of a cylindrical test item with density 1.74 g/cm3 was measured to 7420 m/s. This is 250 m/s below the theoretical calculated value with Cheetah 2.0 at TMD. For a conical charge the detonation velocity between charge diameter 27 mm and 20 mm was measured to 5435 m/s. Detonation pressure measured by Plate Dent gave a detonation pressure of 207 kbar. As for the detonation velocity this result is below the theoretical value calculated by Cheetah 2.0. For the different contents of MCX-6100 due to sedimentation theoretical calculations with Cheetah 2.0 and TEMPER 2.2.2 have been performed. These results show the influence of sedimentation on performance and fragmentation. Porosity has been calculated from the differences in densities between measured and calculated values. The results show highest porosity in the top of the fillings and lowest in the bottom part.
Komposisjonen MCX-6100 er utviklet og produsert av Chemring Nobel AS. Dette er en smeltestøpt komposisjon som primært anvendes som sprengstoff i 120 mm og 155 mm granater. Vi har karakterisert komposisjonen ut fra dens potensiale for bruk i denne type ammunisjon. MCX-6100 har DNAN som bindemiddel. Faststoffet er en blanding av NTO og RDX. Nominell sammensetning for MCX-6100 er 32/53/15 (DNAN/NTO/RDX). Ved å bruke DNAN som bindemiddel kan alle anlegg for fylling av TNT eller TNT-baserte komposisjoner også benyttes til fylling av MCX-6100. Denne rapporten omhandler hvordan MCX-6100 CH 6027/14 er karakterisert med hensyn på kritisk diameter, detonasjonshastighet og detonasjonstrykk. Sedimentering er studert ved analyse av sammensetning i lengderetningen av støpte enheter. For de ulike sammensetningene er det utført teoretiske beregninger av virkning ved bruk av Cheetah 2.0 og for fragmentering med TEMPER 2.2. Røntgen av en sylindrisk ladning viser lavere tetthet i toppen enn i bunnen. Innholdet av luftbobler/porer er i stor grad konsentrert til den øvre halvdel av ladningen. Benyttet prosedyre for støping har derfor potensiale for forbedringer, selv om vakuum var benyttet. Kritisk diameter for MCX-6100 CH 6027/14 er bestemt til 18,5 mm og 19 mm i to tester av to koner. Detonasjonshastigheten er målt for en sylindrisk ladning og for en konisk ladning med største diameter 30 mm. Detonasjonshastigheten for sylindrisk ladning med tetthet 1,74 g/cm3 er målt til 7420 m/s. Målt detonasjonshastighet er 250 m/s lavere enn teoretisk beregnet med Cheetah 2.0. For det koniske testlegemet er detonasjonshastighet mellom ladningsdiameter 27 og 20 mm målt til 5435 m/s. Detonasjonstrykket er målt til 207 kbar ved bruk av Plate Dent-test. Det eksperimentelt målte detonasjonstrykket er som detonasjonshastigheten, noe lavere enn teoretisk beregnet med Cheetah 2.0. For de ulike sammensetningene til MCX-6100 har effekten av sedimentering vært studert ved hjelp av teoretiske beregninger med Cheetah 2.0 og TEMPER. Disse beregningene viser at porøsiteten er høyest i toppen og lavest i bunnen av fyllingene.
View Meta Data